A New LAN Expansion Board (supporting Gbit Ethernet and PoE/PoE+) has been released.

LINEEYE Co., LTD. has released a new LAN Expansion Board, OP-SB89 (which supports Gbit Ethernet and PoE/PoE+ measurement and dedicated to LE-8200/LE-8200A) on May 28.

1. Background

PoE is used to supply power to devices such as network cameras, access points of wireless LAN, and IP telephone, which tend to be installed at places where power supply is not nearby.

OP-SB89 of LINEEYE supports measurement of LAN Data on 10Base-T, 100Base-TX and of PoE. However, support for measurement of Gigabit Ethernet(1000Base-TX) and PoE+ has been strongly needed.

2. Outline

OP-SB89G is an expansion board to be installed to expansion slot of LE-8200/LE-8200A, which supports the measurement and test of Gigabit Ethernet, along with the measurement of PoE and PoE+. You can monitor data frames with highly accurate timestamps and also can transmit any data frame at wire rate to execute a stress test. A utility software to utilize monitored data on PC is attached. OP-SB89G is the latest option with which you can use LE-8200A/LE-8200 as a high-performance stand-alone LAN analyzer on the occasions such as development of devices, installation of devices, and troubleshooting etc.

[ Go to OP-SB89G page ]

3. Feature

It records packets of Gbit Ethernet with timestamps of 40ns at minimum on FPGA of the board.
Measurement by direct tap connection of devices of PoE/PoE+ is possible.
Fail-safe design to maintain the communication between devices when power of the analyzer turns off
Easy to execute a stress test of a network by transmitting test packets at any line bit rate up to 1Gbps
You can convert a captured log to .pcap file (for Ethereal / Wireshark) by using an attached utility software.
Graph display of time-series change of communication traffic and number of error packets etc.

4. Compare OP-SB89G to OP-SB89

	OP-SB89G	OP-SB89
Interface	10Base-T / 100Base-TX / 1000BASE-T	10Base-T / 100Base-TX
Monitor Function	Measurement and logging of LAN data
Trigger	By detection of specific frame or by coincidence with external input level	Coincidence with external input level
Timestamp	13 digits, MIN resolution: 40ns	13 digits, MIN resolution: 1μs
Recording Frame	Max. 48,000-1,048,000 frames (equivalent to 100M byte)	Max. 48,000-1,388,000 frames (equivalent to 100M byte)
Display	Translatable protocol:IPv4, ARP, ICMP, TCP, UDP, DHCP A software to convert to pcap file is attached.
Filter Function	Monitoring of specified frames (disregarding the other frames)
Auto Save	Automatically saves the captured data into an external memory.
Retrieval Function	You can retrieve specified frames and display/count it.
Statistic Function	This function keeps statistics of 2 kinds of frame counters by specified interval (1-240 minute), and display it in a graph. It is possible to display all the frame counter values in real time
PoE Measurement Function	Measurement and continuous logging of the power consumption, Voltage (0-60V), Current (0-600mA), Power type, and OK/NG statement between devices of PoE/PoE+.	Measurement and continuous logging of the power consumption, Voltage (0-60V), Current (0-380mA), Power type, and OK/NG statement between devices of PoE.
PG Function	Transmits up to 16 kinds of packets at specified number of times or continuously It is possible to set frame gap for each packets.	-
PSE Detection	-	Detects a PSE connection to the Port C and lights the LED.
Cable Test Function	-	Measurement of a cable length (3-120m) Detection of short circuit and split pair
Port Blink Function	It is possible to make the link LED of a connected HUB blink periodically
Accessories	Interface expansion board, Line state sheet E, LAN cable, Utility CD	Interface expansion board, Line state sheet C, LAN cable, Utility CD

5. Beginning of shipment

Beginning of June, 2014

6. Contact

Email: Contact Us