PC-connectable protocol analyzer / Data logger
LE-200PR
●2-way operation of PC-connected protocol analyzer / logger
●Remote measurement from PC by Wi-Fi connection
●Supports measurement of arbitoral speed (4 significant digits)
●Continuously recording for a long time on the HDD of PC or the SD card in the unit
●Power failure countermeasure circuit to ensure recording to SD card
●Unattended measurement with specified time by RTC (real-time clock)
●Trigger function to control external signal output terminal and user-defined LED
●Simulation function that can send registered character strings by simple operation
●Small palm-sized body
LE-200PR is a lightweight communication protocol analyzer has a Data Logger function to record data in the SD card for long hours. It is a high performance model, which has same function as LE-200PS and also supports remote control by Wi-Fi.
This model is discontinued. The successor is LE-200PF.
| Interface | Standard: RS-232C /RS-422 /RS-485 Optional: TTL(Model: “OP-5M”) | |
|---|---|---|
| Measurement Connecter | DSUB 25pin, Female connecter (M2.6) | |
| Protocol | ASYNC, ASYNC-PPP, Character SYNC: SYNC/BSC, Bit SYNC: HDLC/SDLC/X.25 | |
| Baud Rate | 50bps~1Mbps (arbitrary) | |
| SYNC Clock | ST1*1, ST2*1, RT(RXC), AR(clock extracted from the edge of SD/RD) |
|
| Data Format | NRZ, NRZI | |
| Data Code | ASCII, EBCDIC, JIS7, JIS8, Baudot, Transcode, IPARS, EBCD, EBCDIK, HEX | |
| Character framing | ASYNC : Data bit (5,6,7,8) + parity bit (0,1) + stop bit (1,2) | |
| Character synchronous : Data bit + parity bit (6 or 8 bits in total) | ||
| Bit synchronous : Data bit (8 bits) | ||
| Parity bit | NONE, ODD, EVEN, MARK, SPACE | |
| Multi-processor bit | MP (multiprocessor) bit is shown with a special mark. | |
| Bit transmission order, Polarity | Order: LSB first/ MSB first (switchable), Polarity: Normal/ Invert (switchable) | |
| Error Check | Parity(ODD, EVEN, MARK, SPACE), Framing, Break, Abort, Short frame, BCC(LRC, CRC-6, CRC-12, CRC-16, CRC-ITU-T, FCS-16, FCS-32. BCC permeation mode | |
| Memory | PC:Max. 16G byte on the HDD, PC-less: capacity of the SD card (specify the file size at 128K /1M /2M /4M /8M /16M byte) | |
| Recording Type | Ring Buffer (continuous) mode, Fixed Buffer (full stop) mode | |
| Mode | Remote mode(with PC), Data Logger mode (PC less) | |
| Measurement start/stop | Control from PC, Start/Stop switch, Auto-Power run, Specify date and time. | |
| Idle Time | OFF(no-record); Resolution: 100ms, 10ms, 1ms; Max. 999. 9s | |
| Time Stamp | OFF (no record); Date time stamp: “Day/Hr/Min”, “Hr/Min/Sec” or “Min/Sec/10ms” | |
| Line Status Measurement | Record signals (RS(RTS), CS(CTS), ER(DTR), DR(DSR), CD(DCD), CI(RI), EXIN) with transmission/reception data. Waveform display (RS-232C only) | |
| Address Filter | Record only frames of the specified address. (HDLC/SDLC/X.25 only) |
|
| Protocol translation display on PC | SDLC (modulo8/128), ITU-T X. 25(modulo8/128), LAPD, PPP |
|
| Trigger | Condition | Communication error, data string up to 8 characters (don’t care and bit mask available), idle time more than the specified duration, matched timer/counter value, logic status of interface signal line, external signal. |
| Action | Capture control (stop, start, or status switching of logging can be specified), Stop measurement (offset can be set), validate/invalidate trigger condition, control timer/counter, send specified data string, send external signal, turn on/ off the light of user defined LED | |
| Retrieval function on PC | Communication error, data string up to 8 characters (don’t care and bit mask available), idle time more than the specified duration, time stamp (don’t care available), trigger-matched data. | |
| Simulation | Transmit data registered in 16 data tables (16K byte) with one pressing a key. DTE/DCE mode selectable. Pre-set the timing of line/data. Insert parity error. |
|
| Conversion | Convert data into Text or CSV format and save. | |
| LED | 5 of two-color LED: Power/ Error, Test/Record, SD/RD, User defined U1/U2 | |
| Switch | One: Run / STOP | |
| External Trigger | Input: 1, Output: 2. 2.54mm pin header connector | |
| SD Card | 2-16G byte*2*2 | |
| USB 2.0 Port | Mini-B connector High speed supported | |
| Wi-Fi interface*3 | IEEE 802.11 b/g/n Frequency range: 2400MHz-2483.5MHz Transmission power: +20dBm(802.11b), +17dBm(802.11g), +14dBm(802.11n) |
|
| Power*4 | Remote mode: USB bus power Remote mode with Wi-Fi / Logger mode: External DC power (DC 7 to 34V, supplied from the DC jack or 25th pin of DSUB connector), AC adapter (6A-181WP09). Power consumption: 1.8W (0.8W when Wi-Fi is OFF, Max.2.2W for about 10sec after turning on). 0.15W/DC24V when turned off. |
|
| Work time during Power failure | 1sec | |
| Ambient Temperature,Humidity | In operation:-10-+55°C In storage: -20-+60°C, 20 - 85%RH (No condensation) | |
| Standard | CE (Class A) | |
| Dimension, mass | 86(W)×130(D)×30(H) mm approx. 220g | |
| Environment of PC | OS: Windows® 7/8.1/10 PC: PC/AT compatible | |
| Accessories | PC software, Mini-USB cable, DSUB 25pin monitor cable, external signal I/O cable, 8G byte SDHC card*2 | |
*1:It is available only for measuring RS-232C.
*2:Only SDHC cards sold by LINEEYE are supported.
*3:Wi-Fi function is available only in Japan, USA, Canada, and EU nations where the product is needed to be compliant with RE directive (2014/53/EU). The Wi-Fi function of this product is set to invalid depending on the country where it is shipped. Please contact LINEEYE for the detail.
*4:AC adapter is sold separately. In the Remote mode (with PC connected by USB), it runs by the USB bus power. In the Logger mode (PC-less) or Remote mode with Wi-Fi, you need to have the optional AC adapter (6A-181WP09) or use the optional Power Plug Cable (SIH-2PG) and external DC power.