PRODUCT
LAN connection type IO controller
LA-5P-P(G)
● LAN interface: 10Base-T/100Base-TX.
● "Email Alert Function" supports the SMTP-AUTH mail.
● One to Multiple TCP connection.
● With an output unit (LA-5R(G) etc.), it can built an input-output system without using a PC.
● 2 types of power supply (AC adapter is an option)
● Various options (DIN-rail mounting plate. Magnets etc.)
● CE marked. EMC(EN61326-1:2013)
Specification
| Model | LA-5P-P | LA-5P-P(G) |
|---|---|---|
| Input circuit | 5 Dry contact inputs | |
| Rated input resistor | off → on 1K Ω or less on → off 10K Ω or more |
|
| I/O terminal | Detachable European terminal 5.08mm pitch, 10 terminals | |
| Applicable wire*1 | Single wire φ 2.06 -φ 0.51mm (AWG24 - 12) Stranded wire 3.31 - 0.21mm2 (AWG24 - 12) Peeled length of the coating: 5mm |
|
| Torque | 0.5 to 0.6 Nm | |
| I/O status display | Input : 5 red LED Power : 1 green LED |
|
| Input signal extension | Function to transmit the input state to the output model LA-5R, LA-5R(G), LA-5T2S, LA-5T2S(G) or LA-5T2S-P. Input chattering filter can be specified. | |
| Pulse count | By 1 specified input terminal, count period (100mS, 1S, 10S, continuous), input chattering filter Input pulses can be counted autonomously by specifying (off, 4mS to 20mS). (Maximum frequency: 4KHz) |
|
| Power supply I/O | DC12V built-in | |
| LAN interface | RJ45 connector 10Base-T/100Base-TX auto-sensing. Ethernet: IEEE 802.3 | |
| LAN protocol*2 | TCP/IP, UDP/IP, ARP, ICMP, SNMP, Telnet, DHCP, BOOTP, HTTP, SMTP | |
| LAN state display | RJ45 connector LED: Indicates LAN connection status (on communication, idle, full duplex, half duplex), panel PWR LED*3 | |
| Port number*4 | TCP, 10003*5, 30718*6 | |
| TCP simultaneous connection | 1 | 4 |
| ID setting | No.0 to 15 (16 positions, can be selected by the rotary switch.)*7 | |
| Email alert | Does not support SMTP authentication mail | Supports SMTP authentication mail |
| Corresponding contact of mail alert function | DI1 to DI5*8 | |
| Power | DC8 to 30V Non-polar, Maximum 3W 2 inputs, DC-IN1 (AC adapter jack) or DC-IN2 (pin header type 2-pin connector)*9 |
|
| Temperature and humidity conditions | Operating temperature: -20 to 55℃ Storage temperature: -25 to 75℃ Humidity: 10 to 95% RH (no condensation) |
|
| Atmosphere | No flammable or corrosive gas. There should be no excessive dust (especially conductive dust) | |
| Noise resistance | ±1500Vp-p, pulse width 50nS/1µS, normal/common mode. Checked by the noise simulator | |
| Withstand voltage | No description | |
| Insulation resistance | 50 MΩ or more at 500 VDC megger, between all inputs and chassis, and between all inputs and all power supplies | Conformed standard | RoHS10 | RoHS10 CE(classA), EMC(EN61326-1 : 2013) |
| Dimensions/&Weight | 74x106x30mm（WxDxH), about 280g | |
| Mounting | Just be put on the site or can be fixed using the M3 screw holes on the back of the main unit. Can be mounted on a 35mm DIN rail using the separately sold DIN mounting plate (SI-DIN70/SI-DIN30) |
|
| Accessories | Utility & sample software CD, power cable, instruction manual, warranty card | |
*1 Use bar terminals for stranded wires.
*2 User applications cannot use protocols other than TCP/IP and UDP/IP.
*3 For the (G) version you can check the TCP connection status by change of the color of the PWR LED.
*4 If access to the relevant TCP/UDP port is blocked by a software firewall, etc. due to security policies, etc., change the settings to allow communication. Similarly, when relaying through a router device, etc., allow communication on the corresponding TCP/UDP port.
*5 It can be changed to any port number other than WELL KNOWN PORT NUMBERS.
*6 This is not necessary when connecting directly by IP address without searching for LANIO units.
*7 Since No.15(F) is used for setting the input extension function, No.0 to 14 can be used as device IDs.
*8 When one of the corresponding contacts (multiple designations possible) is turned on (or off), one point of mail alert function operates.
*9 DC-IN2 is compatible with the attached power cable or the separately sold power branch cable. When making your own cable, use wires of AWG#24 to 22 size, J.S.T. Mfg. Co., Ltd. housing (XHP-2) and crimp contacts (SXH-001T-PO.6).