LINEEYE OP-SB89G

OP-SB89G is an expansion board for Ethernet LAN (supporting Gbit), inserting into a slot of portable communication analyzer (LE-8200A/LE-8200). It is a stand-alone LAN analyzer, exchanging the measurement board and line state sheet for LAN signals. The monitor function measures data at real time by simply connecting the LAN cables. The packet generation function transmits frames from the analyzer at wire rate. It supports PoE (Power Over Ethernet) and PoE+ standards, and able to analyze the communications and power consumption at the same time.

Comparison table of OP-SB89G, OP-SB89E, and OP-SB89

Image of Use

Easy setup for a Gbit LAN (PoE supported) analyzer !!

Once the firmware of OP-SB89G (attached to the product) is written to the analyzer, it can be used as a stand-alone analyzer that supports LAN communication and PoE measurement simply by replacing the interface board.

Exchanging the boards (sample image)

LAN Measurement Port PORT A	Fail-safe TAP when using On-line monitor, PoE/PoE+ measurement, Statistic analysis function. LAN port of 10BASE-T/100BASE-TX/1000BASE-T when using PING, Port blinking, PG function.
LAN Measurement Port PORT B	Fail-safe TAP when using On-line monitor, PoE/PoE+ measurement, Statistic analysis function.
External Triger Port	Automatically stops the on-line monitor when external signal connected to the TRG IN terminal becomes “L” level.

The line state sheet for the measurement target is attached. It fits snugly into the line-state LED part of the analyzer.

LED		Monitor
Link A	ON	PORT A Link-up
	OFF	PORT A Link-down
	Blinking	PORT A Receiving data
Link B	ON	PORT B Link-up
	OFF	PORT B Link-down
	Blinking	PORT B Receiving data
1000BASE-T	ON	1000BASE-TX connection
100BASE-TX	ON	100BASE-TX connection
10BASE-T	ON	10BASE-T connection
Full Duplex	ON	Full Duplex connection
Full Duplex	OFF	Half Duplex connection
PoE TAP type A	ON	PoE Alternative A detected
PoE TAP type A	OFF	PoE Alternative A not detected
PoE TAP type B	ON	PoE Alternative B detected
PoE TAP type B	OFF	PoE PoE Alternative B not detected

Monitor Function

It monitors Ethernet LAN and records the 10BASE-T/100BASE-TX/1000BASE/T data frames in the capture memory up to 100M bytes. It displays data on the LCD or filter only specific frames. It has the Fail-safe TAP no to affect the communications between the devices when power shortage of analyzer.

< Filter setting >

< Monitoring >

Data Use

Measured data can be converted into pcap format by the utility software (lepcapcvt), and analyzed using the Ethereal and Wireshark (free software). Furthermore, data can be used in the PC by transferring it via the external memory card.

*1 A USB cable is not provided with the product. Prepare a USB cable if you intend to use USB connection. The LE2-8V AUX cable provided to the analyzer is available in the case of serial connection.

*2 LE-8200A/LE-8200 can save data in the CF card. An interface to read the CF card is required on the PC side.

*3 LE-8200A can save data in the USB flash drive.

< Screen of utility software "lepcapcvt" >

< Example of using data on the Wireshark >

■Transmits packets up to 1Gbps line rate.

Packet Generator function transmits the test packets at specified rate to evaluate the processing ability of network devices and to check the action of the devices under the high traffic. Test packets are generated in the FPGA, so it will not be affected by the performance of PC.

■Specifies test packets

Specifies frame data of 2 - 7 layers up to 16 kinds and transmits them continuously or specified times. Configuration of transmission frames is easy because Ethernet, Ipv4, ARP, ICMP, TCP, UDP are prepared for each protocol.

Statistic Function

Communication traffic and numbers of error packets can be calculated and displayed in graphs.

< Graph display >

< Counter display >

Total	Total reception frames
Good	Normal frames
Broadcast	Broadcast
Multicast	Multicast
Pause	Pause frames
Length1	Numbers of packets of 0 – 63 byte
Length2	64 byte packets
Length3	Numbers of packets of 65 – 127 byte
Length4	Numbers of packets of 128 – 255 byte
Length5	Numbers of packets of 256 – 511 byte
Length6	Numbers of packets of 512 – 1023 byte
Length7	Numbers of packets of 1024 – 1518 byte
Length8	Numbers of packets of 1519 byte or more
CRC error	CRC error
Alignment error	Alignment error
Fragment error	Fragment error

PoE Measurement

OP-SB89G has the isolation transformer for PoE/PoE+ and connects not only the common LAN cables but also the LAN cables for PoE/PoE+ devices. It is able to use as the Power logger of PoE and also communication analysis.
PoE/PoE+ measurement data can be saved in the external memory as CSV format file and used by the table calculation software on the PC.
It can measure the Voltage, Current, Power consumption of PD devicek and record mas 4 million of data and tell the statement (OK/NG). It is useful for the devices when it is hard to get their power source, such as Network cameras, access points for wireless LAN, IP telephones.

< Connection image of using Dummy port >

< PoE measurement >

< PoE graph >

< PoE dump display >

PING function, Port-blinking function

OP-SB89G has the PING function for linking test, and port-blinking function to find the specific cable to easily fin the cable from the large numbers of other cables. This is not only useful for developing LAN devices but also for installing the LAN devices in the building.

< PING setting >

< PING display >

< Connection image of Port-blinking >

Print function

Measured data (PoE Overview) can be printed in following format.

LAN frame

*=[LE-8200]=====[2014-06-05 10:52:08]=*
* Model     : LE-8200                 *
* Version   : 1.00                    *
* Extension : OP-SB89G                *
* Serial No.: ********                *
* Start time: 2014-05-14 13:23:15     *
* Stop time : 2014-05-14 13:24:08     *
*-------------------------------------*
*  PROTOCOL: LAN                      *
*=====================================*

---Date---------Time------------Source----------Destination-----Protocol---
2014-05-14 13:23:20.96710000 D4-AE-52-CC-01-94 33-33-00-01-00-02 IPv6
2014-05-14 13:23:20.96730000 D4-AE-52-CC-01-94 33-33-00-01-00-02 IPv6
2014-05-14 13:23:21.20790000 10-6F-3F-B3-56-DC FF-FF-FF-FF-FF-FF [8899]
2014-05-14 13:23:21.20810000 10-6F-3F-B3-56-DC FF-FF-FF-FF-FF-FF [8899]
2014-05-14 13:23:22.96780000 D4-AE-52-CC-01-94 33-33-00-01-00-02 IPv6
2014-05-14 13:23:23.20780000 10-6F-3F-B3-56-DC FF-FF-FF-FF-FF-FF [8899]
2014-05-14 13:23:23.23830000 0.0.0.0           255.255.255.255   DHCP
2014-05-14 13:23:23.23960000 00-A0-DE-3F-B0-9C FF-FF-FF-FF-FF-FF ARP
2014-05-14 13:23:23.30610000 00-26-18-4E-C1-54 FF-FF-FF-FF-FF-FF ARP
2014-05-14 13:23:23.33990000 192.168.0.1       192.168.0.24      DHCP
2014-05-14 13:23:23.34030000 0.0.0.0           255.255.255.255   DHCP
2014-05-14 13:23:23.34180000 192.168.0.1       192.168.0.24      DHCP
2014-05-14 13:23:23.34230000 0.0.0.0           255.255.255.255   DHCP
2014-05-14 13:23:23.34350000 00-A0-DE-3F-B0-9C FF-FF-FF-FF-FF-FF ARP
2014-05-14 13:23:23.44380000 192.168.0.1       192.168.0.24      DHCP
2014-05-14 13:23:23.44420000 0.0.0.0           255.255.255.255   DHCP
2014-05-14 13:23:23.44570000 192.168.0.1       192.168.0.24      DHCP
2014-05-14 13:23:23.48400000 00-C0-EE-4B-59-5E 09-00-07-FF-FF-FF SNAP
2014-05-14 13:23:23.89540000 00-24-A5-4B-8A-86 FF-FF-FF-FF-FF-FF [8899]

LAN detail

*=[LE-8200]=====[2014-06-05 10:52:08]=*
* Model     : LE-8200                 *
* Version   : 1.00                    *
* Extension : OP-SB89G                *
* Serial No.: ********                *
* Start time: 2014-05-14 13:23:15     *
* Stop time : 2014-05-14 13:24:08     *
*-------------------------------------*
*  PROTOCOL: LAN                      *
*=====================================*

-----dTime----------Source----------Destination-----Protocol---
   --------    D4-AE-52-CC-01-94 33-33-00-01-00-02 IPv6
 Ethernet II
  Destination: 33-33-00-01-00-02
  Source: D4-AE-52-CC-01-94
  Type: IPv6 (0x86dd)
  FCS: 65 3A 8B B8
 Data
  Length: 136
 0000:  60 00 00 00 00 60 11 01 FE 80 00 00 00 00 00 00
 0010:  20 8B F3 6B 66 B9 FA 3A FF 02 00 00 00 00 00 00
 0020:  00 00 00 00 00 01 00 02 02 22 02 23 00 60 63 55
 0030:  01 13 90 0D 00 08 00 02 00 00 00 01 00 0E 00 01
 0040:  00 01 19 5E EA 7B D4 AE 52 CC 01 94 00 03 00 0C
 0050:  0F D4 AE 52 00 00 00 00 00 00 00 00 00 27 00 0A
 0060:  00 08 79 61 73 65 72 76 65 72 00 10 00 0E 00 00
 0070:  01 37 00 08 4D 53 46 54 20 35 2E 30 00 06 00 08
 0080:  00 18 00 17 00 11 00 27
-----dTime----------Source----------Destination-----Protocol---
0000000.000200 D4-AE-52-CC-01-94 33-33-00-01-00-02 IPv6
 Ethernet II
  Destination: 33-33-00-01-00-02
  Source: D4-AE-52-CC-01-94
  Type: IPv6 (0x86dd)
  FCS: 65 3A 8B B8
 Data
  Length: 136
 0000:  60 00 00 00 00 60 11 01 FE 80 00 00 00 00 00 00
 0010:  20 8B F3 6B 66 B9 FA 3A FF 02 00 00 00 00 00 00
 0020:  00 00 00 00 00 01 00 02 02 22 02 23 00 60 63 55
 0030:  01 13 90 0D 00 08 00 02 00 00 00 01 00 0E 00 01
 0040:  00 01 19 5E EA 7B D4 AE 52 CC 01 94 00 03 00 0C
 0050:  0F D4 AE 52 00 00 00 00 00 00 00 00 00 27 00 0A
 0060:  00 08 79 61 73 65 72 76 65 72 00 10 00 0E 00 00
 0070:  01 37 00 08 4D 53 46 54 20 35 2E 30 00 06 00 08
 0080:  00 18 00 17 00 11 00 27

PoE text

*=[LE-8200]=====[2014-06-05 10:52:08]=*
* Model     : LE-8200                 *
* Version   : 1.00                    *
* Extension : OP-SB89G                *
* Serial No.: ********                *
* Start time: 2014-05-14 13:23:15     *
* Stop time : 2014-05-14 13:24:08     *
*-------------------------------------*
*  PROTOCOL : IEEE 802.3af            *
*       TYPE: Altanative A            *
*        PSE: Port A                  *
*        PIN: 1,2 Pin                 *
*=====================================*

------TM-----------POWER-------VOLTAGE------CURRENT-------
0,000,004.565         --         +1.2          --
0,000,004.570         --         +0.9          --
0,000,004.575         --         +0.5          --
0,000,004.580       +6.3        +46.1        +137
0,000,004.585       +6.4        +46.1        +139
0,000,004.590       +6.5        +46.1        +143
0,000,004.595       +1.8        +46.9         +40
0,000,004.600       +2.0        +46.9         +43
0,000,004.605       +1.9        +47.1         +42
0,000,004.610       +0.4        +47.2         +10
0,000,004.615       +0.8        +47.0         +18
0,000,004.620       +3.0        +46.6         +66
0,000,004.625       +0.5        +47.1         +12
0,000,004.630       +0.3        +47.2          +8
0,000,004.635       +0.7        +47.1         +16
0,000,004.640       +2.9        +46.7         +64
0,000,004.645       +4.0        +46.7         +86
0,000,004.650       +0.3        +47.2          +7
0,000,004.655       +0.7        +47.1         +16
0,000,004.660       +3.2        +46.6         +69
0,000,004.665       +1.8        +47.0         +39
0,000,004.670       +1.8        +46.9         +40

PoE CSV


913,--,+1.2,--
914,--,+0.9,--
915,--,+0.5,--
916,+6.3,+46.1,+137
917,+6.4,+46.1,+139
918,+6.5,+46.1,+143
919,+1.8,+46.9,+40
920,+2.0,+46.9,+43
921,+1.9,+47.1,+42
922,+0.4,+47.2,+10
923,+0.8,+47.0,+18
924,+3.0,+46.6,+66
925,+0.5,+47.1,+12
926,+0.3,+47.2,+8
927,+0.7,+47.1,+16
928,+2.9,+46.7,+64
929,+4.0,+46.7,+86
930,+0.3,+47.2,+7
931,+0.7,+47.1,+16
932,+3.2,+46.6,+69
933,+1.8,+47.0,+39
934,+1.8,+46.9,+40
935,+1.8,+46.9,+39
936,+1.7,+46.9,+38
937,+1.8,+46.9,+39
938,+1.7,+46.9,+37
939,+1.6,+46.9,+36
940,+1.7,+46.9,+37
941,+1.7,+46.9,+38