CAN/LIN Line monitor
LE-170SA
●Supports CAN and LIN
●4.3 inch color touch screen
●Real-time display of communication data
●Supports USB flash as strage device
●Handheld, 5 hours work by AA size Ni-MH batter
LE-170SA is a compact hand-held size line monitor for CAN/LIN. It has a touch screen and can be control as for smartfones. It has 1 CAN channel and 1 LIN channel and it can monitor both CAN and LIN communication thus monitoring of the network which has both CAN and LIN is available. The monitor function can diplay the communication data in real-time while saving it. The simulation function can send/receive the test data instead of the original communication partner. The ID filtering and trigger function make your development/evaluation more efficient. It also can measure 4 external signals as degital signals or analog signals while monitoring the communication data. It is light (300g) and convenient for field testing. The line monitor is useful for not only development but also maintenance.
| Interface | CAN (ISO11898) / LIN (ISO9141), (Dsub 9-pin male, inch screw #4-40) |
|---|---|
| Protocol | CAN 2.0LIN (Rev. 1.1, 1.2, 1.3, 2.0, 2.1) |
| Capture Memory | 16Mbyte (acout 4000Kdata), 2 part division is available |
| Speed (bps) |
CAN: 20kbps to 1Mbps LIN: 400bps to 26kbps |
| Capture memory | 16Mbyte (about 500K data). Able to divide in two. |
| Monitor function |
CAN: Standard/extended format are supported, bit receiving timing can be set, filtering is available, arbitrary speed can be set.
LIN: Divides the frame by specified time pass or ID setting, filtering is available, arbitrary speed can be set. |
| Auto run/stop function*1 | It can automatically start and finish measurement at the specified time at the selected repeating cycle (monthly, daily, hourly). |
| Power ON auto run function*1 | It can automatically start measurement when power is turned ON. |
| Auto save function*1 | Automatically saves the monitored data in the capture memory and saves as communications log file in a USB flash memory. Restart mode and Append mode (which are ring save operation) and Max mode (in which the measurement stops at the specified capacity.) can be selected. |
| File size | BUF (capture memory size) , 1MB , 2MB , 4MB , 8MB |
| MAX. files | 256 |
| Simulation function | Test data transmission (data sweep is available.) |
| External Trigger | Input 1, Output 1 |
| External input | 44 Measurement of 4 signals. Range: 0 to 52V. Resolution: 12bit. Digital threshold: VIH 2.3Vmin. VIL 0.8Vmax. |
| Display | 4.3 inch TFT color display (480x272dot) 28 characters x 6-stage display |
| Touch panel | Capacitive touch screen |
| USB2.0 device port | Micro B connector |
| USB2.0 host port | Standard A connector for USB flash connection | Power | USB bus power 5V/500mA Two AA Ni-MH batteries or two AA alkaline batteries (LR6) |
Drive time*2 | AA Ni-MH batteries: about 5 hours AA alkaline batteries: about 2 hours |
Temperature & humid | 0 to 40 degrees celcius (-10 to 50 degrees celcius for storage), under 85%RH | Standard | 158mm x 100mm x 31mm, 300g(including batteries) | Size & weight | CE (class A), EMC (EN61326-1:2013) | Accesories | DSUB9 pin branch cabale (LE-009M2), 10 pin external In/Out cable (LE-10ES1), micro USB cable, 2 AA Ni-MH batteries, utility CD, carrying bag (LEB-02), quick start guide, warranty card |
*1: Available by the firmware ver.1.01 or later
*2: Based on our testing by common usage.