SI-65

●Connects 10Base-T/100Base-TX by auto-detection.
●Supports multi protocols such as TCP/IP, UDP/IP, ARP, etc.
●Automatically controls RS-485 communications, which is available to use the flow control of XPort®.
●Able to control 128sets maximum in RS-485 multi-drop type.
●Can use in the workplace environments between -10 to 50 degree Celsius.
●Solid, card-case sized, and metal enclosure.
●Supports installation of 35mm DIN rail.
●Environment-friendly design. Use lead-free solder. Non-use of chromium screw etc.

SI-65: Japanese model (100V Input AC adapter)
SI-65-E: World wide model (Wide Input AC adapter )

SI-65 is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
The built-in Lantronix Xport® on the LAN interface converts RS-422/RS-485 data into LAN protocol (TCP/IP). It also transfers LAN data, controlling RS-485 driver automatically. It has the robust metal body and supports 35mm DIN rail. Therefore, you can use it for factory automation without worry.

Overview

Specification

Option

Download

■Block Chart

■Appearance

The images are CAD data image.

■Interface Description

RS-422/485 terminal

6 terminals terminal block, easy to use for wiring at the site

Number	Name	Full duplex^*1		Half duplex^*1
Number	Name	I/O direction^*2	Description	I/O direction^*2	Description
1	SD+	Out	Send data+	-	Cannot used^*3
2	SD-	Out	Send data-	-	Cannot used^*3
3	SD/RD+	In	Receive data+	I/O	Send/Receive data+
4	SD/RD-	In	Receive data-	I/O	Send/Receive data-
5	GND	-	Signal ground	-	Signal ground
6	+5V IN	-	External power input		External power input

*1: Can be switched by the dip switch B.

*2: "Out" means when signal outputted from the converter and "In" means when signal is inputted. Both direction is "I/O".

*3: Do not connect anything when in half duplex mode.

LED

LED	Description
SD	Lights when data comes from LAN to RS-422/485.
SD/RD	Lights when data goes RS-422/485 to LAN.
DRIVER ACTIVE	Lights when the RS-485 driver of the converter is active.
PWR	Lights in green when powered.

Dip switch SW-A

Can set RS-422/485 driver control method and value of internal timer for the line monitoring.

SW1	SW2	SW3	Internal timer (mSEC)	Speed(bps)
OFF	OFF	OFF	57	More300
ON	OFF	OFF	14.3	More1200
OFF	ON	OFF	7.1	More2400
ON	ON	OFF	3.6	More4800
OFF	OFF	ON	1.8	More9600
ON	OFF	ON	0.9	More19200
OFF	ON	ON	0.45	More38400
ON	ON	ON	0.11	More115.2K

SW4	OFF	Sets the driver in active by the status of common IO pin CP2 of the XPort (for RS-422).
SW4	ON	Automatically sets the driver active when transmitting RS-422/485 signals (for RS-485).

Dip switch SW-B

Can select the communciation method of RS-422/485 and terminal resistor.

SW	Function	OFF	ON
SW1	Method	RS-422 (full duplex)	RS-485 (hull duplex)
SW2	Receives the echo of transmitted data.	Yes	No
SW3	Terminal resistor between SD+ and SD-	Open	100Ω
SW4	erminal resistor between SD/RD+ and SD/RD-	Open	100Ω

■Connection example

In addition to the installation and screwing using the M3 screw holes on the bottom, you can use the optional DIN mounting plate (SI-DIN70) or DIN vertical mounting plate (SI-DIN30S) to mount to a 35mm DIN rail. You can also mount the by using the wall mounting bracket (SI -WM1) with screwing from the front.

< DIN Rail Installation Example >

< Optional "Metal Fitting for Wall" >

■A Useful Tool for Multiple Operation

SILANIOinit is a configuration tool for LINEEYE products embedded WiPort-NR. It is useful and saves time to rewrite the WiPort-NR configuration file (Setup Record) .

［ Functions ］

Searches the device on the Network. Displays the MAC address.
Reads and saves the configuration (set-up record) of converter.
Writes to the set-up record of selected converter.
Sets the IP address of selected converter.

< Configuration tool (SILANIOinit) >