Firmware Version History for LE-7200/LE-3200/LE-2200/LE-1200

Version. 1.12 Jul. 30, 2010

• Add the function in the BERT which external trigger output will be LOW when detecting the error bit.
  After the test (finish the each time of REPEAT mode), it will become HIGH automatically.
• Able to use the 2G byte CF card for LE-1200.

[ detail ]

Version. 1.11 Sep. 17, 2009

Specification change

• Add a display mode for ASYNC frame per a time stamp
• Add the display of difference between two time stamps.
  (Press [SHIFT] + [TIME/COUNT]. Cannot be used while measuring.)
  
• Change the default of “FRME TIME” to 5ms (It was 100ms) at the Configuration menu.
  (It will be recognized as a frame end if there are no communications for more than 5ms in the case of ASYNC.)
• Correct miner bug of Bit Shift Display on BURST data.
• Correct miner bug of changing display code when turning of the power.

[ detail ]

Version. 1.10 Oct. 27, 2008

Specification change

1. Accepts the bigger size of CF card. (only for LE-3200/2200/1200.LE-7200 supports 8Gbyte as same as before.)
   

   Model	New Firmware(V1.10)	Before(1.09)
   LE-1200	1G Byte	512M Byte
   LE-2200	2G Byte	1G Byte
   LE-3200	2G Byte	1G Byte

2. Supports the active type of Simulation of OP-1C (adapter for current loop).
3. Adjusts the timing of start/stop conditions of I²C.
4. Corrects the miner bug of MBA process for file management.
5. Corrects the problem that stopping the process when pressing the incorrect key for auto configuration.

[ detail ]

Version. 1.09 Jun. 21, 2007

Specification change

1. Revised the time display between cursors in the Logic Analyzer function.
   Corrected the counting number to be 1ms after it counts 999us.
   (It used to be 10ms instead of 1ms)
2. Corrected the timing signal in the LCD display.

[ detail ]

Version. 1.08 Mar. 31, 2006

Specification change

1. Added REPEAT (repetitively measuring) mode to the test mode of BERT.
2. Added Print out/TEXT output function of BERT measurement result at the time of REPEAT mode of BERT.
3. The frame end detection time of ASYNC and Burst can be set within the range of 1 to 100 ms.
4. Accelerated the time when turning RS-422/485 driver OFF after data transmission on driver control AUTO of simulation function.
5. The measurement information other than the monitor data can be transmitted and received remotely when measuring (in RUN).

[ detail ]

Version. 1.07 Nov. 30, 2005

Specification change

Optimized the software process related with power consumption.

Bug Fixes

Target Model : LE-7200-E, LE-3200-E, LE-2200-E

1. Added the process not to do synchronism reset when monitoring the data of the transparent mode of SYNC-BSC.
2. Fixed a minor bug of the station address setting process at the polling simulation.
3. When performing reappearance transmission of the data in the buffer whose final data is the frame terminal data other than time information at the buffer simulation, a bug to which inaccurate data is outputted was fixed.

Version. 1.06 Jun. 30, 2005

Specification change

The specification had been changed so that the remote operation from PC link software cannot change AUX communication condition of analyzer.

Bug Fixes

1. Corrected the problem that "," which should be inputted by "D" key cannot be inputted on the editing operation of the transmission data table when the data code setting is ASCII.
2. Corrected the problem that the red light LED of the clock signal ST1, ST2 and RT is not lighted, and the same clock signal cannot perform logic analyzer. (This problem happens only on the firmware V1.05 of LE-7200, LE-3200 and LE-2200)

Version. 1.05 May 19, 2005

Bug Fixes

Correct the problem with margin for the decode circuit of IrDA.

Version. 1.04 Apr. 27, 2005

Supported larger-capacity memory cards.

Firmware	Ver.1.04	Ver.1.03
LE-7200	6G bytes	4G bytes
LE-3200, LE-2200	1G bytes	512M bytes

Bug Fixes

1. Corrected the problem that an external trigger setting (RISING and FALLING) operated reversely with actual input logic.
2. Corrected the following problem: when the total data of transmission data table shows the odd number, saving the setting file with simulation programs into a memory card causes to stop operating with the exception screen appear.
3. Corrected the following problem: by using the auto save and auto run functions together, when the auto run is in the ON setting, the exception screen stops operating after the auto stop stops operating.

Version. 1.03 May 11, 2004

Expands the AUTO RUN function

1. Added the function to repeatedly start and stop measurement at the appointed time (monthly, daily, hourly).
2. Added the function to automatically start measurement after powering on analyzers.

Expands the AUTO SAVE function

1. Added the function to append data to a file.
2. Improved safety and high-speed access by changing file access system
   

   Previous specifications:	Damages the file when power is down during running.
   Current specifications:	Damages the file when power is down during running and accessing to CF or HDD cards.
   * When power is down during accessing to CF or HDD cards, it may damage them. Therefore, do not let power down when using this function.

Filter function

Added the filter function to the file table which lets you check information by kinds of data, file, time, and stamp.

* Users of the PC Link software LE-PC300 are required to update to version 1.00.03.

Bug Fixes

Corrected errors that had caused to display incorrectly after the search was completed.

Version. 1.02 Jun. 15, 2003

Bug Fixes

1. Corrected the problem with printing without the BCC OK data at the time of printing the screen for the normal data and line status.
2. Corrected the problem that the wrong name of a signal line was shown when V.35 data was displayed on the wave monitor screen.
   ** The associated data file conversion program has been also updated.

Version. 1.01 Jun. 3, 2003

Bug Fixes

Contact

Email: Contact Us