Multi Protocol Analyzer
LE-2500XR
●4.3 inch color touch screen
●RS-232C, RS-422/485, TTL (UART/I2C/SPI) as standard
●Supports HDLC/SDLC, I2C, and SPI measurement tests as standard
●Supports CAN, CAN FD, LIN, CXPI etc. by optional expansion set
●Secure long-term recording on USB flash or SD card by AUTO SAVE
●High precision time stamp of hour, minute, second, 10msec
●Logic analyzer analysis and signal voltage measurement
●Supports PC connection and remote control by Wi-Fi
LE-2500XR: Japanese model (with Japanese manual)
LE-2500XR-E: Abroad model (with English manual)
The LE-2500XR is a standard model of a stand-alone communication protocol analyzer which has a touch panel color display and adopted lithium ion battery while inheriting all the functions of the conventional model LE-2500/LE-2500R which have the monitor function, simulation function, and bit error rate test function necessary for communication analysis test.
Visualization of signal status and error data on the line monitor display is dramatically improved by colorizing the display. With the touch panel and the physical key switch, you can optimize the use of them - for example, swiping of the touch screen for display of a large amount of communication monitor data and key operation for MANUAL simulation mode (in which communication test data are assigned to the keys and transmission/reception test is executed). In addition, many key operations of the conventional model are inherited as shortcut key operations.
The newly designed housing is significantly smaller and lighter than the conventional model, reducing the burden for maintenance of communication device and trouble shooting of communication systems.
LE-2500XR is a high cost performance product which can be widely used for RS-232C serial communication around PCs, trouble analysis of RS-422/RS-485 lines of FA equipment, embedded development of I2C, SPI and UART devices, and in-vehicle communication test of CAN, LIN etc.
| Item | Name | Remarks |
|---|---|---|
| Expansion kit for CAN FD/CAN/CXPI | OP-SB7XC | |
| Expansion kit for CAN FD/CAN/LIN | OP-SB7XL | |
| Expansion kit for current loop comm. | OP-SB1C | |
| Expansion kit for TTL/I2C/SPI | OP-SB5GL | For TTL(USART) |
| Expansion kit for RS-530 | OP-SB10N | For RS-530/V.24 |
| Firmware for high-speed communication | OP-FW10XR | For high-speed CC-Link/HDLC/SPI, max.10Mbps |
| 32GB SDHC card | SD-32GX | |
| DSUB25pin monitor cable | LE-25M1 | Note: same as the attached one |
| DSUB9pin monitor cable | LE-259M1 | For RS-232C of DSUB9 pin |
| DSUB9pin branch cable | LE-009M2 | Same as the attached one |
| X.21 monitor cable | LE-25Y15 | For DSUB15 pin X.20/21. Y-type branch |
| RS-449 monitor cable | LE-25Y37 | For DSUB37 pin RS-449. Y-type branch |
| V.35 monitor cable | LE-25M34 | For M-type 34pin V.35 |
| RS-530 cable | LE-25S530 | For RS-530 of DSUB25 pin |
| 5 wires TTL prove cable | LE-5LS | Same as the attached one |
| 10-pin external I/O cable | LE-10ES1 | Cable with 1 pin connector each for TTL measurement port |
| PC link software | LE-PC300R | Note: This software does not support OP-SB7GX. |
| PC link software | LE-PC7XCL | For OP-SB7XC/OP-SB7XL |
| USB charger | LE-P2USB | 1.8m with A-B connector |
| Carrying bag | LEB-01 | Note: same as the attached one |
| Battery pack | P-26LS1 | For replacement. Same as the attached one |
| 3.81mm pitch terminal block (5 terminals) | LA-5ETB45 | For replacement. Same as the one attached to the RS-422/RS-485 measurement port. |
| Small mobile printer | SM4-31W | The Lightweight, robust, waterproof and dustproof (equivalent to IP54) battery-powered printer. You can print communication data, statistical analysis information, measurement conditions, etc. measured with a compatible LineEye communication analyzer on site without using a PC. |