LINEEYE LE-PC800G Version History

HOME >> Support > Update > LE-PC800G Version History

Update

In the remote monitor mode, 16M, 32M, 64M, 128M bytes are added to the selectable block size (file size) and the recording capacity has been increased to 256Gbyte.
Adds the configurated value of idle time and time stamp to the header of the output text by text conversion.
Fixed the bug on the data property display.

Increases the number of simulation data tables up to 160.(before 16 tables)
Supports PROFIBUS protocol.
Adds following menu.
Flow control ON/OFF. (BERT function)
Half-duplex Simulation mode. (Interface setting)
Waiting mode (power off) and power check (AUTO RUN/STOP setting)
Prohibits Simulation and BERT. (other setting)
PULSGEN mode (for LE-8200A only. Cannot edit waveform data)
Adds "TRG OUT" in the trigger action setting of OP-FW12G.
Supports OP-FW12GA.
Corrects the bug of CSV conversion (when selecting "SD"/"RD" only, per a frame) for MODBUS data.
Corrects the bug on simulation program ("SET REG" command. "INC", "DEC").

Add following short-cut keys for data search function

Add the character search in the search conditions.
The previous "Character search condition" is renamed as "Character (HEX) search condition".
Support Modbus protocol.
Record in another data files after appointed time.
Add the starting options.
-r "[name of configuration]"
After starting the LE-PC800G, selected LE-8200 which is set by the configuration starts measuring automatically. (able to set more than one LE-8200)
-q
Adjust the format of data files to enable to read the files immediately.
Increase the maximum block number (number of files) from 2000 to 2048.
Save the search conditions after closing the application.
Change the name of starting menu for On-line help as "LE-PC800G help".
Correct the minor bug of character input mode for data tables.

Display each communication frame in different line for ASYNC/SYNC protocol.
(Break signal of ASYNC is displayed as “?b”)
Display property of measured data. [file menu] -> [data property]
Support expanded time stamp.
Add On-line Help
Add “Cut/Copy/Paste” functions in the transmission data table on Simulation feature.
Change the zoom switching display from combo box to track bar.
Pause the display of “Delay/ Flow/ Polling (master/slave)” while measuring.
Able to select data table number “0-9” by TEN key.
Transmit the break signal by “*” key in Manual mode.
Support digital waveform monitor function on OP-FW12G.
Add “Manchester0/ 1” on HDLC data format.
Add “10ns” on clock configuration in the digital waveform monitor.
Add “Min/ Sec” on TREND time setting in the analyzer.
Add “SEND BRK” command in the program editor in Program mode.
Add “MSB first/ LSB first” on bit sequence on the SPI configuration.
Add “50000, 200k, 417k” on I²C baud rate.
Add “Stop” on BT RUN lock setting.
Change the icon of tool bar to full color.
Move the “Remote setting list” button next to “Remote setting” button.
Display the name of some icons by right clicking on tool bar.
Change the selection of SYNC/ HDLC clock to “TXC_IN/ TXC_OUT/ RXC/ AR” for OP-SB85(L).
Convert ASYNC measured data into CSV. Each frame is divided by time stamp.
Save text CSV conversion setting.

[Bug correction]

Correct the bug that some data with control lines is not converted into text properly.
Correct the bug that frame divided by time stamp is not outputted after CSV conversion.
Correct the bug that “excepting time stamp/ idle time” is not functioned properly. (Text conversion)
Correct the bug of PPP/ I²C/ SPI translation conversion when setting of “number of character: Max”. (Text conversion)
Correct the bug of CSV conversion ended in error after “receiving BERT result and conversion”.
Correct a minor bug of program editor in Program mode.
Correct a minor bug of HDLC X.25 packet translation display.
Correct a minor bug of IrLAP text conversion. “NS” and “NR” are displayed in opposite place.
In the test conversion of LAPD frame translation, “None” is displayed when the last bit of RD is “0”. In the previous version, “INFO” was displayed.
Change the specification of “A1h” for EBCDIC and “7Fh”/ “BFh” for EBCDIK, to be same as LE-8200.
Correct other minor bugs on configuration.

[Add/Improve/Change]

Add the display of PPP translation/IrLAP translation/I²C frame/SPI frame.
Add the configuration of Analog Wave Monitor when using the OP-SB85/85L.
Change the name of "Wave Monotor" to "Digital Wave Monitor" in the analyzer setting.
Compatible with OP-FW12G. Firmware of OP-FW12G has to be V2.00 or later.
ASYNC Frame end characters can be max. 2 characters and able to set "dont care".
(Firmware of LE-8200 has to be Ver1.05 or later.)
Increase the numbers of characters per line when converting into the text file.
(approx. 1M characters.)
Increase the number of columns to set when converting into CSV file.
(Max.255 -> Max.265535)
Add the transmission/reception of simulation programs, save, and load functions.
Add the seclection of whether or not transmit/receive the simulation programs.
Add the program editor (leprogedit) from program mode in the analyzer setting.
Shorten the error detection time such as disconnecting the USB cable.
Able to set the max. COM port numbers by direct input.
Add the spin button when inputting numbers.
Change the dialog of "open file" and "save file" to the OS standard.
Change the title and signal name of ECHO mode.
Change the design on the menu bar in the Windows® Vista.
Change the design on the text conversion window in the Windows® XP/Vista.
Compatible with USB driver (V2.06) for Window.

[Debug]

Correct the displayof configuration dialog in the Windows® Vista.
Correct the bug of not displaying the time stamp for 100,10, 1μs.
Correct the miner bug of speed setting for SPI communications.
Correct the miner bug of scrolling when HDLC translation display.
Correct the bug that test modes of ECHO mode cannot be applied.
Correct the bug that the order of RI/TRG control lines cannot be applied.
Correct the miner bug about POLLING master mode.
Correct the bug that BERT measurement data excepts REPEAT mode cannot be saved.
Correct the bug that selection of translation format cannot be applied.
(it is always "SD&RD")
Correct the minier bug of key operation when text conversion.
Correct other bugs.

Improve the data transferring speed for key emulation screen, especially for the serial and the LAN connection (SI-60).
(Firmware of analyzer is V1.04 or later.)
Add format type of bit map file to "gray scale" other than "color" when saving on the Key Emulation.
*Improve system to avoid blockages by a security software.

Add a setting item in the dialog of analyzer setting.
Correct the bug of calculation of the time stamp.
Correct the bug that high resolution time stamp is not displayed in the translation display.
Correct the bug of timer counter while measuring.
Correct the bug that LE-PC300F does not work when using with LE-PC800G.
Correct the bug that reception process of buffer data process ends as errors.
Correct the bug that character find cannot specify the bit masks (W0-W2).

LE-PC800G released